Guides / Ceiling Systems
An aluminium baffle ceiling is a row of vertical aluminium blades suspended with a gap between each blade, so the ceiling stays open in one direction while the blades absorb sound. With acoustic infill the system typically reaches NRC 0.60–0.95, and blade spacing runs from 150 to 400 mm depending on how open you need the ceiling. This guide sets out what a baffle ceiling is, how the blades and spacing do the acoustic work, and how to write the specification so the supplier quotes the same ceiling you drew.
An aluminium baffle ceiling is a series of vertical blades hung with a gap between them, so air and services still move through the ceiling while the blades take the edge off the room acoustics. The blades are carried on a hidden grid, and the void above stays visible and reachable from below.
Three numbers define the system before anything else: the blade shape, the gap between blades, and whether acoustic infill is fitted inside the blade. Blade width runs 100 / 150 / 200 / 300 mm, spacing is normally 150–300 mm (wider at 200–400 mm for a more open look), and the five blade shapes carry different airflow, lighting and absorption. The absorption figure you reach is set by the infill and the spacing, not by the bare aluminium.
A baffle ceiling is a metal ceiling built from vertical blades rather than a flat panel face. Because the blades are open in one direction, the plenum above stays part of the room: air moves through, sprinklers can see down, and services stay reachable. This is the same reason an open cell ceiling leaves the void exposed, but a baffle ceiling opens in one direction only.
It is easy to confuse a baffle ceiling with its neighbours. A linear metal ceiling is a run of planks that close off the void; a baffle ceiling is the same family of blades, but separated by gaps. A solid panel ceiling has no openings at all. The linear, baffle or cell comparison sets out where each family belongs.
It is also called a blade ceiling. Whatever the name, the specifier buys it on three numbers: blade module, the gap between blades, and the carrier grid they clip to.
Bare aluminium reflects sound. The absorption in a baffle ceiling comes from the acoustic infill fitted inside or behind the blade, and from vertical blades exposing more surface to the room than a flat panel of the same footprint. Perforated blades let sound reach the infill behind the metal face.
Absorption is measured as a Noise Reduction Coefficient, tested to ASTM C423 — the share of sound that hits the surface and is absorbed rather than bounced back. On the blade systems we quote, the range is NRC 0.60–0.95 with infill fitted, set by the blade shape, the spacing and the infill, and confirmed for your project rather than assumed. The baffle ceiling page lists the absorption range for each blade shape.
A baffle ceiling reduces reverberation inside a room; it does not block sound travelling between rooms, because the gaps let air — and sound — pass through. If the brief is separation, a baffle ceiling alone will not deliver it.
The blade profile sets the airflow, the lighting detail and the absorption range all at once. The five profiles we quote are U-shape, round tube, A-shape, teardrop and bullet.
| Blade shape | Airflow | Lighting integration | Acoustic (NRC) | Typical spacing |
|---|---|---|---|---|
| U-shape | High | Linear LED in blade | 0.70–0.90 with infill | 150–300 mm |
| Round tube | Highest | Linear LED inside tube | 0.60–0.80 with infill | 200–400 mm |
| A-shape | High | Linear LED in groove | 0.75–0.95 with infill | 150–300 mm |
| Teardrop | Medium | Linear LED in profile | 0.65–0.85 with infill | 200–350 mm |
| Bullet | Medium | Linear LED in profile | 0.60–0.80 with infill | 200–400 mm |
The figures are with acoustic infill fitted, taken from the baffle ceiling page. Absorption is confirmed for your project rather than assumed.
The gap between blades trades three things against each other. Tight spacing puts more blade surface into the room, raising absorption and reading as a denser ceiling. Wide spacing opens the ceiling for airflow and keeps more of the services above visible.
Spacing is normally 150–300 mm; where the design calls for a more open look or higher airflow, 200–400 mm is typical. Fix the spacing in the enquiry and let the supplier confirm the blade size and infill that reach the absorption figure you need — two baffle ceilings that look the same can differ by a full spacing step, and the quotes are not comparable until that number is locked.
Blade shape and spacing are the first two lines, not the whole list. The blade also has a width, a thickness, an edge height and a finish, and each appears on the quotation.
| What you specify | Common range | Why it matters |
|---|---|---|
| Blade width | 100 / 150 / 200 / 300 mm | Narrow blades read as a fine line; 300 mm reads as a plank |
| Aluminium thickness | 0.6 – 3.0 mm | Priced on a sliding scale per 0.1 mm step |
| Edge height | 20 / 24 / 28 / 30 mm | Sets the carrier and the clip |
| Blade spacing | 150–300 mm (200–400 mm open) | Trades absorption against airflow and visibility |
| Acoustic infill | In or out | The absorption comes from the infill |
| Finish | Powder coat / PVDF / anodized / wood-grain / stone-grain | Finish tier adds a per m² premium |
| Accessories | Carrier, clips, trim | Quoted separately unless included |
These values are the production specification on the baffle ceiling page. Send the drawing and the sizes are confirmed against it before quotation.
On the enquiry, state the blade shape, spacing, width, thickness and alloy, whether infill is required, and the finish. Lighting is often coordinated in the same drawing — linear LED is commonly carried inside the blade or in the groove between blades — so give that detail at the same time. Price is a separate question, covered on the baffle ceiling price page.
The system earns its keep in high, open volumes where airflow, lighting and sound absorption all have to be solved at once — atria, airport concourses, metro stations and hotel lobbies, spaces that would echo with a hard flat ceiling and where the services above still need to breathe.
It is not the first choice for a quiet office or a corridor, where a flat panel or a linear plank gives the cleaner line and the better acoustic surface. That decision is set out in the linear, baffle or cell comparison.
It is a row of vertical aluminium blades suspended with a gap between each blade, so the ceiling stays open in one direction. The blades are carried on a hidden carrier grid, and the space above remains visible and reachable for air and services.
The vertical blades expose more surface area to sound than a flat panel, and the absorption comes from the acoustic infill fitted inside or behind the blade. With infill, blade systems typically reach NRC 0.60-0.95 depending on the blade shape and spacing.
Spacing is normally 150-300 mm, and 200-400 mm where a more open look or higher airflow is wanted. The spacing is confirmed against your drawing, because it trades acoustic coverage against airflow and visual density.
They are closely related. A linear ceiling is a run of planks that close off the void; a baffle ceiling is a series of vertical blades with gaps between them, so air and services move through the ceiling in one direction.
Standards are cited for the definitions and methods they contain. The absorption figure for a project comes from the acoustic design, agreed with the supplier, not from this page.