Guides / Ceiling Pricing
A 1200 × 600 acoustic ceiling tile does not have a price of its own. What you are quoted is a system price — panel, finish, thickness, grid and accessories — and two quotes for the same room diverge because they are built from different inclusions. This guide breaks the price into its parts so a quotation can be read line by line.
Start with the panel, not the price. 1200 × 600 describes the module the tile is cut to, the edge detail that sets how it sits in the grid, and the finish on the visible face. Those three choices, plus aluminium thickness, quantity and accessories, are what move the number. A quote that gives one per-square-metre rate without stating those inputs cannot be compared to a second quote, because the two may not be pricing the same tile.
So the practical answer to “what does a 1200 × 600 acoustic tile cost?” is: ask what the rate includes, and hold the inputs constant before comparing.
The figure is a module size — a tile measuring 1200 mm by 600 mm — and it says nothing about the material, the edge or the finish. When a specification is written as a size alone, three separate decisions are still open:
Standard modules on the ceiling systems page run from 300 × 300 up to 800 × 800 mm, with 600 × 600 and 600 × 1200 the common commercial sizes; lengths can be cut to a drawing. The module you choose has to match the grid the services and lighting are set out on.
A ceiling quotation is not one number. It is a set of line items, and the fastest way to see why two quotes differ is to lay them out side by side against the same list.
| Line item | What it is | Usually quoted |
|---|---|---|
| Ceiling panels | The aluminium tiles or planks themselves, at the specified module, thickness and finish | Per m² or per set, by quantity |
| Grid / keel | The main runners and cross tees that carry the panels, or the concealed carrier for clip-in tiles | Per m² or per linear metre |
| Suspension | Hangers, clips and fixing to the soffit or slab | Often separate |
| Perimeter trim | Wall angle or shadow trim closing the ceiling at the room edge | Per linear metre |
| Acoustic infill | The absorbent layer behind a perforated tile, where acoustics are specified | Separate when specified |
| Cutting & waste | Cut-to-drawing lengths and the allowance for offcuts at the perimeter | Inside the rate, or added |
Accessories — grid, suspension, trim and infill — are quoted separately unless they are written into the initial enquiry. A quote that bundles panel and accessories is easier to compare than one that splits them.
Whatever the module, the price of a metal ceiling system tracks the same five inputs. Hold four constant and change the fifth, and you can see exactly what is driving the difference between two offers.
Send the same drawing to three suppliers and you can still get three different totals. Almost always it is one of these, not a magic price difference:
Put the items from the table above on one sheet, mark what each quote includes, and the comparison stops being a guessing game.
A ceiling quotation comes back firm when the enquiry carries the inputs. Five things are enough:
Send a drawing for a firm per-project ceiling quote
The full module sizes, edge options, thickness range and finishes are on the ceiling systems page. If you are still choosing between linear plank, baffle and open cell, the ceiling system comparison sets out the decision. Documents that Gulf and Asian customs expect are covered on the certifications page.
There is no single rate, because the tile is one part of a system. The price depends on the aluminium thickness (0.6–3.0 mm), the finish tier, whether the panel is perforated with acoustic infill, the quantity, and whether grid and trim are included. Send the module, finish and drawing for a firm per-project figure rather than comparing bare per-square-metre numbers.
The tile is the same rectangle; the difference is the direction it is laid and how it aligns with the grid, the lighting runs and the services setout. State the orientation on the drawing, because it changes the grid layout and the cut schedule at the perimeter.
Not by default. Grid or keel, suspension, clips and perimeter trim are quoted as separate line items unless they are requested in the initial enquiry. Ask for them bundled if you want to compare on total supply rather than panel rate.
Usually because the two quotes do not contain the same things — different finish, different thickness, or one includes grid and trim and the other does not. Hold the inputs constant, then compare. A lower panel rate with accessories added later is often not the cheaper supply.
Quotes reference the current ingot price on the quote date and hold that rate for the validity period written on the quotation. After the validity period the price is re-based to the prevailing market price. The validity for standard finishes is typically short, and longer for a firm order with a deposit.
Yes. Panels are cut to the module and edge detail on your shop drawing, and lengths can be made to order, so the perimeter trim and cut schedule come from the drawing rather than a standard sheet size. Confirm the cut schedule with the enquiry so the waste allowance is priced deliberately.
Lead time depends on the finish, the quantity and the container load; it is confirmed at enquiry stage. Standard powder-coat colours run faster than wood-grain, stone-grain and anodised finishes, and a drawing-matched cutting schedule affects the programme.